Temperature and Water Requirement for Leaching of Caustic Alkalt From ‘ngu   Abstract of Temperature and Water Requirement for Leaching of Caustic Alkalt From ‘ngu The production and analysis of “Ngu” extract for temperature and water requirement for leaching of casuistic alkali is the basic objective of this project.  The production was carried out by…

Construction of 2,000 Litres Capacity Water Re-servoir   Abstract of Construction of 2,000 Litres Capacity Water Re-servoir In the construct of 2,000 litres capacity water reservoir galvanized  steel  sheet forms the tank and an angle iron rod forms the stand.  Two full length galvanized sheet were marked out and cut out to the required sizes. …

Crises Management in Industrial Environment   Abstract of Crises Management in Industrial Environment A study was carried out on crisis management which originated with the large scale industrial and environment disaster in the 1980’s. Crisis management is the process by which an organization deals with a major event that threatens to harm to the organization,…

Production of High Quality Liquid Air Refresher   Abstract of Production of High Quality Liquid Air Refresher A project was carried out to produce high quality liquid air refreshner for domestic uses. The project was carried out using the following apparatus. Beakers (250ML), one conical flask, hydrometer, thermometer, two – 5ml of measuring cylinders, one…

Refining of Vegetable Oil With Enugu Coal   Abstract of Refining of Vegetable Oil With Enugu Coal This project was carried out using acid activated coal from Enugu coal and the production of ve4getablew oil was monitored using spectrophotometer to measure the absorbance. It was also perform to check the suitability of activated Enugu coal…

Industrial Wastewater Treatment Technology in Petroleum and Chemical Industrial   Abstract of Industrial Wastewater Treatment Technology in Petroleum and Chemical Industrial Industrial wastewater treatment covers the mechanisms and process used to treat water that have been contaminated in some way by anthropogenic industrial or commercial activities prior to its release into the environment or its…

Construction of Soap Cutting Table, Soap Mould and Soap Cutters   Abstract of Construction of Soap Cutting Table, Soap Mould and Soap Cutters The construction of soap cutting table, mould and cutters became inevitable as it’s importance in our industries and society could not be over emphasized. When one considers the money at hand, he…

Construction of a Steel Cupboard   Abstract of Construction of a Steel Cupboard The aim of this project was to construct a steel cupboard in order to help us acquire the knowledge of fabrication of a modern cupboard and the essence of it. Also to enable us (the students of chemical Engineering) to know how…

Construction of Cellophane Sealing Machine   Abstract of Construction of Cellophane Sealing Machine The construction of the callophane sealing machine was carried out.  The project started with an encompassing review of the various methods of heat sealing film packages.  The machine can be used in sealing both low, medium and high-density cellophane.  The product has…

Presentation on the Construction of S Liter Electric Kettle   Abstract of Presentation on the Construction of S Liter Electric Kettle The construction of the five (5) litre Electric Kettle was carried out in mechanical workshop of the Institute of Management and Technology Enugu. (I.M.T). The fabrication process, included measuring and marking out operations of…

Formulation and Production of Alcohol From Palm Wine   Abstract of Formulation and Production of Alcohol From Palm Wine This research work was arrived as the formulation and production of ethanol (ethyl alcohol) from the fermentation of palm wine. A fresh palm wine was ated which was obtained  from Emene in Enugu State.  The characteristics…

Effect of Interface on the Quality of Petroleum Product in Multi Purpose Pipeline System   Abstract of Effect of Interface on the Quality of Petroleum Product in Multi Purpose Pipeline System Interface on petroleum product in multi-purpose pipeline system refers to as the zone of demarcation between two products where mixing occurs.  Generally, interface is…

Dehydration of Ethanol Water Solution Using Activated Starch   Abstract of Dehydration of Ethanol Water Solution Using Activated Starch This project research work was based on dehydration of ethanol water solution using activated starch. The extracted starch obtained was of whistler method. The starch obtained from potato was weighed with the use of a weighing…

Process and Quality Factors in Laundary and Toilet Soap Production   Abstract of Process and Quality Factors in Laundary and Toilet Soap Production This projects is aimed at knowing the process and quality factor in Laundary and Toilet Soap Projection.  Various factors affected the quality of the soap produced.  These include the method used in…

Report on Fabrication of Flow Nozzle   Abstract of Report on Fabrication of Flow Nozzle The flow nozzle was constructed based on the dimensions and specifications of the international standard organization (I.S.O) recommendation. Throat diameter 42.5mm Length converging nozzle 68mm Thickness of nozzle 2mm Diameter of major axis of ellipse 85mm Diameter of minor axis…

Extraction of Wax From Cocoa Pod                            Chapter One of Extraction of Wax From Cocoa Pod INTRODUCTION The word wax describes a large variety of substances of plant and animal origin, as well as man made products which are mostly petroleum derivatives. However, natural waxes are not single substances, but a mixture of various of…

Construction of Kerosine Cooking Stove   Abstract of Construction of Kerosine Cooking Stove The purpose of the construction is aimed at producing heat energy for commercial use by turning liquid fuel(kerosene).the construction was successful by appropriate selection of engineering material favourably mild steel(blacksheet) and steel iron for special p2rts. The technological properties passed by the…

Construction of Soap Cutting Device   Abstract of Construction of Soap Cutting Device The aim of the project is to construct a soap cutting device capable of size-remaining the soap produced into regular bars and tablets without error in shapes and sizes. Soap cutting devices are used to size reduce or cut the bulk of…

Construction of Simple Distillation Unit   Abstract of Construction of Simple Distillation Unit Distillation unit is the judgment used for the separation of liquid mixture depending on the volatility of the component. It has the top section and bottom section. In the top section this is where more volatile component goes and the bottom section…

Construction of Propeller Agitator   Abstract of Construction of Propeller Agitator The construction of propeller agitator used for agitating and mixing of low viscous fluid was fabricated in the mechanical workshop of the institute of management and technology Enugu. In the construction, galvanized mild steel was chosen due to its inherent properties.  After procurement, the…

Construction of Simple Metallic Mould                            Chapter One of Construction of Simple Metallic Mould INTRODUCTION The equipment mostly used in the industries and manufacturing establishments requires the production of definite shape, pattern, different design, embossments and others, are usually moulds.  The ability of moulds to withstand pressure, distortion and corrosion determines the application. A mould…

The Construction of Sand Filter for Portable Water Filtration With Stainless Steel Material   Abstract of The Construction of Sand Filter for Portable Water Filtration With Stainless Steel Material The project constructed was sand filter; equipment for portable water filtration.  This was constructed using a mild steel material.  This was because of the excellent high…

Construction of Office Table and Chairs   Abstract of Construction of Office Table and Chairs Office table and chairs usually come in set of three, and are designed to fit one into another for convenient storage. Furniture of this soot should be of the highest quality, attractive in design and capable of standing up to…

Construction of Aluminium Wall Rack   Abstract of Construction of Aluminium Wall Rack This project was constructed with the desired materials of construction. The materials include aluminum, glass and wood.  Aluminum was used in forming the skeleton of the structure, glass was used for the doors while wood was used in the sides, top, base…

Construction of Air Conditioning Unit   Abstract of Construction of Air Conditioning Unit The project of construction is one (1) horse power Air conditioning unit which was executed successfully.  With up to seventy five percent (75%) efficient performance. The project started with the construction of the size of the air conditioning unit.  The air conditioning…

Construction of Heat Exchanger Fabrication of a Tube and Shell Heat Exchanger System   Abstract of Construction of Heat Exchanger Fabrication of a Tube and Shell Heat Exchanger System There are two methods of constructing heat exchangers: Plate type.  Parallel flow-the hot fluid and the coolant flow in the same direction. Counter flow:-           The hot…

Construction of a Distillation Column With Reflex Divider and Condenser   Abstract of Construction of a Distillation Column With Reflex Divider and Condenser In this project, distillation is made up of a column, condenser and reflux divider. An overview of the dimensions of some of the major parts is: Height of the column = 450mm…

Construction of a Model Shell and Tube Heat Exchanger   Abstract of Construction of a Model Shell and Tube Heat Exchanger The precise content of this project was to construct a model shell and tube heat  exchanger. The material for construction of this project (equipment) and their dimensions are as follows: 500mm length of a…

Construction of a Chemical Rack, Study Apparatus   Abstract of Construction of a Chemical Rack, Study Apparatus The construction of the 500 gallous (2,250 litre) of water is a project which has definite mathematical patterns. The choice of a cylindrical pattern of design involved the application of mathematical deductions to analyse the size of materials…

Construction of Hydro Cyclone   Abstract of Construction of Hydro Cyclone A cyclone is an equipment or a device used for the separation of dust particles from air, which has no moving component parts. This mechanism can also be defined as a system of winds circulating about a center of relatively low barometric pressure and…